Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Are you looking for critical information concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging project. If the old tub is readily easily accessible, the job can move rapidly; if you need to open up a wall to eliminate the old tub as well as position the new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. See to it you have actually certified yourself for the task and also are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will help you install a brand-new bath tub in your bathroom if you have actually already acquired a brand-new bathtub and do not require to transform the plan of your previous water system pipelines.
Your devices and also product list should make up the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bathroom should be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to prevent strain on the tub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply as well as check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub and likewise check the overflow outlet as well as the typical outlet for leakages.
Lastly, take care of the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub needs to wait until the bathtub has actually been made use of at least once as this will settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines are in place between the faucet and the sink. Safeguard the faucet in place with the maker given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous type must be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, causing the water to permeate the wall in between the bathroom and the tiling, causing problems with dampness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly offered on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that article on Installing A Bathtub from someone on another blog. I beg you take a moment to promote this entry if you enjoyed it. Thanks a lot for your time. Don't forget to come by our website back soon.
Tap leaking? Call us. Report this page